Skaitmeninis daugiafunkcinis testeris | TRUE RMS | 6000 AUTO LCD (YT-73096)

Automatic range: Yes Frequency measurement: 0-9.999MHz AC voltage measurement: 0-750V + True RMS DC voltage measurement: 0-1000V Capacitance measurement: 0-9.999mF Resistance measurement: 0-9.999MΩ Duty cycle measurement: 1-99% Alternating Current: 0-9.999A + True RMS DC current: 0-9.999A Continuity test: YES Diode test: YES Product description Universal meter YT-73096 with TRUE RMS function and automatic range for each measurement. It enables basic and advanced measurements of electrical quantities. Popular housing, small dimensions and a large backlit display combine high mobility with comfort of work. The speed, accuracy and repeatability of indications of the multimeter is due to the modern design of the control board and high-quality measuring probes, the size and precision of which will be appreciated by both hobbyists and professional service technicians. BASIC MEASUREMENTS AC voltage measurement: A.C. 0-750V, TRUE RMS DC voltage measurement: D.C. 0-1000V AC current measurement: A.C. 0-10A, TRUE RMS direct current measurement: D.C. 0-10A resistance measurement: 0-60MΩ diode test: IF 5mA, UR 3V continuity test: 0-50Ω ADDITIONAL MEASUREMENTS capacitor capacity measurement: 0-9.999mF frequency measurement: 0-9.999Mhz measurement of the fill factor: 1-99% MEASUREMENT ACCURACY An example of determining the accuracy for the measurement of AC voltage. Calculation for the measurement result: 235V The accuracy of the measurement of the YT-73096 meter for this range is: ± (1.0% + 3), resolution 0.1V calculation of measurement error formula: (measurement result x 1.0%) + 3 x resolution calculations: (235 x 1.0%) + 3 x 0.1 = 2.35 + 0.3 = 2.65V The actual result, taking into account the measurement error, for the reading of 235V = 235 ± 2.65V result taking into account the measurement error for the DC voltage measurement indication: 12V = 12 ± 0.09V result taking into account the measurement error for the indication of the alternating current intensity: 8A = 8 ± 0.15A The table with the resolution and accuracy for a given measurement can be found in the user manual. BUILT-IN FUNCTIONS TRUE RMS - a meter with this function calculates the real effective value of AC voltage and current for both sinusoidal and non-sinusoidal waveforms. The device first measures the real value of the sine wave in several time intervals → then squares the measurement results → sums them up → calculates the mean → and finally the mean result takes the square root. The measurement result is a real RMS voltage / current, even for a deformed sinusoid or square wave. AUTO - automatic adjustment of the measuring range. If you measure unknown values with a handwheel manual ranging, take measurements sequentially from the largest range up to the range giving the most accurate result - otherwise you risk damaging the device. However, in the case of a multimeter with the AUTO function, it is enough to take one measurement and the meter will automatically find the optimal range. By default, the meter starts in the AUTO mode SEL - change of measurement mode, e.g. from AC to DC voltage measurement DATA HOLD - saving the currently measured value on the display ADDITIONAL INFORMATION LCD display, the maximum displayed result: 6000 screen backlight acoustic signal in the circuit continuity test for resistance below 50 Ω possibility to enable diode and circuit continuity tests separately 14.5 cm long measuring probes included cable length with probes: 97 cm wire diameter with insulation: 3.5 mm construction with overload protection ABS housing automatic shutdown of the meter after 15 minutes of inactivity the ability to disable the automatic shutdown mode of the device low battery indicator power supply: two 1.5V (AAA) batteries Parameters Auto range: YES Frequency measurement: 0-9.999MHz AC voltage measurement: 0-750V + True RMS DC voltage measurement: 0-1000V Capacitance measurement: 0-9.999mF Resistance measurement: 0-9.999MΩ Duty cycle measurement: 1-99% Alternating Current: 0-9.999A + True RMS DC current: 0-9.999A Continuity test: YES Diode test: YES